Recensioni dei clienti per VEVOR Troncatrice Circolare Elettrica a Taglio Freddo per Metallo Lama Diametro 35,5cm Angolazione tra 0-45° Potenza Nominale 2800W, Troncatrice Circolare Taglio Freddo Velocità a Vuoto 1200 giri/min

After the first cut I made using this saw I was very excited and happy because the material cut was a 105mm full steel cylinder, medium hard, and the blade was cool after the job. The motor block was just around 40 degC. Fantastic, in my judgement. The second cut was finished in the next 15 to 20 minutes and that was also to my satisfaction, given the really heavy job at hand. I attempted the third cut on the same stock and have realized that something went wrong. The grinding noise told me that. It became louder and louder and then, I noticed the blade was out of alignment. I started panicking and the motor kept working until it stalled. At that moment the blade was warped by several centimeters out of the plane. It took several seconds before I turned the machine off. Analyzing the event I concluded that the massive size of the material and its round shape made it too difficult to hold it in place at all times so it shifted axially. Then I realized how good this product is. It survived so much abuse and it is still working. I would only recommend replacing of the half-nut vice with something better or an improved version of it. I did not see spare blades listed on this website. I believe, with respect to my experience described, it is a very tough product worth investing in it. I recommend the machine.

Compré tronzadora y mesa VEVOR. La mesa muy alta y más alta al colocar la tronzadora. La mesa sin cartelas para aguantar su escuadra, una tostada en el medio y ruedas que tiembla toda la mesa. La tronzadora : El primer corte corta con más o menos suavidad... Pero el trozo sobrante de unos 20 cm hizo un ruido como un petardo .. pegó en el techo y luego en el cristal de mi BMW rompiéndolo. Asustado. Lo dejo. al

The saw and blade make nice clean cuts, however making accurate cuts is painful at best. If all you want to do is make square cuts it might be okay. That said there are a number of massive issues. The base is not flat or sqaure to the blade. On my saw this is especially bad if trying make 45 degree cuts. To get the material sqaure to the blade there is a 5mm gap under the material at the blade. The other massive issue is that it is impossible to clamp the material at angles and it gets worse as the angle increases. At 45 degrees any amount of clamping pressure will cause the fence to rotate and change the angle

Kam beschädigt an und auch die Lager machen laute Geräusche. Keine Reaktion vom Kundenservice. Ganz schlechter Service und ganz miese Kommunikation!

Stopped working after second use. Customer service is putting off a refund or replacement for days at minimum.

I spent extra to get the better saw and got something with very poor build quality. When you start the saw it sounds awful, like it’s rubbing but nothing is visible. When you bring the blade down to cut it almost rubs on the right side of the cutting channel. I cut one piece of material and it went OK but on the second piece as the blade was cutting it hit the side of the cutting channel and the entire saw jumped out of my hands. It hit hard enough to bend the original blade. I purchased the more expensive blade with more teeth but after installing it I’m not willing to use this is again, it’s dangerous with the blade coming down so close to the side of the cutting channel. I should have looked this over more carefully when I first received the saw and sent it back. What a waste of $300 so beware. Check your saw thoroughly. I know some of you got decent saws, mine is junk. This is not letting me upload photos either. Interesting.

As described, the clamp isn't the best quality have trouble holding the metal properly when cutting

I've had minimal use of this saw since purchase, though can say I'm happy with how its cuts mild steel 25mm x 8mm and 1/2” tubing with ease. The only down side I’ve found with this saw, is that the base isn't perfectly flat, it could do with a thinker more robust base, and the clamping jaws are rather weak in design, and adjusting protractor isn't perfect, so don't expect precision cuts. Lastly I think VEVOR should offer “more spares items” for these types of tools, example an additional parts accessories lists, like blades, drills

Good heavy duty saw that makes good smooth cuts that are cool to touch right after making the cut. Used cutting 1/8 4x4 square tubing and up to 5/16 4" flat bar. My only complaint is that the angle fence isn't true and you need to check your angles with a square before making any cuts.

This size very poorly designed. It cuts fine but the fence is crooked and hard to use. I also had to get the saw fixed by an appliance maintenance place because it didn't work when I got it