Recensioni dei clienti per VEVOR Estrattore di Miele Elettrico in Acciaio Inox, 4/8 Favi, 140W, Velocità Max 1300 Giri/Min, Smielatore Centrifuga per Apicoltura con Coperchio Trasparente, Altezza Regolabile 100-108 cm

Bonjour J'ai bien reçu mon extracteur de miel électrique commandé mais par contre la cuve avait un pète j'ai du la redresser et le joint de la valve couper en deux

Pretty decent little machine for the price. Extracts well. The plastic covers at the top are quite fragile, though, and break easily. Mostly they're just to keep stupid people from putting their fingers into the machine while it's working, though, and take five minutes to remove entirely. After that, keep your fingers out! One thing worth noting was that the feet were just tack-welded on and have zero strength re: attaching this to the floor or to a chunk of plywood for stability. I had to take the legs to a welder and have the feet properly welded on and it cost me another $100 to get that done. I suppose I could've sent it back to Vevor, but I needed to harvest my honey and didn't have time to wait on a replacement. The tub itself is solid, and is easy to clean afterward with a hose. The legs have two positions -- tall and short -- and I'd advise attaching them short and then securing this to a floor or something else heavy and sturdy or else the whole thing will try to walk away on you while it's running.

This honey extractor has the same issue like all extractors they can wobble around a fair bit when the honey frames are unbalanced. Just need fixing in place so they do not 'walk' across the floor when trying to extract honey. If the RPM could be slightly higher would make for a more timely extraction but gets the job done.

Works well as an extractor once you have stabilised it. The supplied legs are useless and cannot dampen the vibration of extracting. If you can change to stiffer legs it is a good working extractor for the price. Also make the new legs longer as original is too low to put a pail under with a strainer.

Overall, great experience and works well. Must be bolted down to floor to use, but then must be unbolted to get all honey out of bottom. That's a litte frustrating.

Since we were new to bee keeping we didn't want to spend a lot of money on a higher end extractor. we didn't known if we were going to stick with bee keeping so getting something more affordable was why we went with this extractor. We purchased knowing that if we were going to keep moving forward with bee keeping that we would probably use this extrator one or two harvest seasons then move up to something bigger. This was easy to put together and did good for our first two seasons. I did figure out that that the metal isn't as high grade as other industry extractors. At the end of our first season cleanup from harvesting I didn't get the extractor completely dry and eneded up getting ow rust on it. It was easily cleaned up with Bar tenders friend compound. It did a great jo restoring the metal. It operated as expected. We have now purchased a bigger different brand extractor and ended up selling thr vevor to a new bee keeper who is going start bee keeping this year. It will serve them well. We have not regrets purchasing thr vevor extractor and would recommend it to anyone who's not sure how far into bee keep they want to go and trying to save some money.

This extractor worked well for me. Nice and quiet and easy to use. We did 25 frames this time without problem. It did wobble unless i held it down (i didn’t bolt it down) but discovered the easiest way to keep it from wobbling and vibrating was to suspend a mass (20lbs or weights) under the drum. Worked good for me

Neat and tidy once you get set up. It is tricky to clean up and replace the spindle in the correct position so you don't scrub out the rubber stoppers but once you know it is ok. No different to another of these i have used. So this one is great for the price.

Over all satisfied with the purchase. Easy to assemble and easy to move from one place to another, not heavy at all. Tried to extract 4 medium frames radially, but wasn't happy about the outcome. Too much of honey left in the frame. Then I tried extracting frames tangentially, putting frames parallel to the walls. Using this method you need to extract one side and then reverse the sides and extract again. So it is a bit time consuming. The other problem is the drain cap is about inch above the bottom, so get all the honey out you need to tilt the extractor which is a pain. Overall happy with the performance.

Works great. Wobbles if you don't brace the legs. A simple 2x4 T plate reduced the wobble a lot. Other than the drain being to high up it is a good unit overall. Would buy again!