Recensioni dei clienti per VEVOR Incudine Acciaio 110,2 libbre 50 kg Incudine in Acciaio Blu Forgiatura Rivettatura Appiattimento Formatura del Metallo Lavorazione dei Metalli Trattamento

I’m pleased with this anvil, solid, good face. It was delivered very quickly. The only issue I have was that there was a bunch of Bondo on the underside and the horn had cast marks on it. I highly recommend this anvil.

Ricevuta in tempi brevi, di buona qualità, superficie un po' troppo facilmente scalfibile, ma complessivamente buona per piccoli lavori DIY

I've been using this anvil for alittle over a month and it seems to be a great anvil for a low cost. It has great rebound and has been able to do what I need it to do. It has a few small flaws but for the price you can deal with it.

I'm not a blacksmith, I dont know what a pritchard hole is. I'm just a dude who hammers on ordnance at a BRACed munitions depot for money. I found the scavenged railroad tie plate they gave me for this purpose too soft and bouncy. The anvil surface is hard and flat, and the round horn is handy for opening up pinched 37mm's for inspection and clearing. It has been sitting exposed to cold and very damp weather for a few days and doesn't show any rust yet. The blue paint comes off onto everything that conctacts with it. The casting is rough at the holes in the feet and very sharp in places. I was hoping to lag screw the anvil to a log I was given for a pounding station, but the feet holes are unsuitable for this. I'm not sure if that's a normal anvil feature. I chiseled a pair of recesses into my log so it sits secure enough. Shipping was pretty quick. All in all, I say it beats the hell out of using a tie plate.

Haven't had the time to mpunt it yet, but I did get to hammer on it a little and it's good; the package was obviously dropped and the box was torn, and I had to do the requisite flap wheel dance to slightly round the corners and get rid of paint from the horn, but otherwise I'm pleased with the purchase.

Excellent value. Not a “perfect “ anvil, but fully functional and all working surfaces flawless. Pritchel hole is too large and in a bad position. I machined an adapter that works pretty well. Rebound is better than my old anvil but not as good as some. However rebound is related to hardness and too hard would make it prone to chipping. I’m happy with it.

I bought this anvil for two reasons. 1) It has an HRc hardness of ~55, instead of only ~50 which is what the blue ones are. 2) Because the picture shows the horn and round hole being flush with the flat surface of the top of the anvil. This second reason turned out not to be the case. There is about a 1/ to 3/8 inch step there. I have since learned that the step is useful for some things but it does mean the round hole is not the same height all the way round, which makes it less useful for using it as a Pritchard hole. I plan to weld some fender washers onto the end of a pipe that will fit in that hole, and then grind one side flat to fit in the hole and solve this problem. The anvil itself is quite good, and for the price is down right amazing. Edges are sharp, so you can break the corners with a file to set the corner radiuses at the size you want. The anvil rings a bit, but I think with a magnet under the horn and a chain around the base this tones it down nicely. (other anvils also ring and can be quieted the same way)

Should give me alot of years of service,thanks vevor for giving good products at great prices with exceptional customer service.

The horn could be more smooth. I will have to grind it. One of the holes should have been square, but both holes are round. Apart from these things, I am satisfied.

Je suis contente de l'enclume, mais je l'ai reçue avec l'emballage déchiré. Il aurait fallu un emballage plus solide, car il était un peu léger par rapport au poids de l'enclume.