Recensioni dei clienti per VEVOR Sollevatore Idraulico a Ponte per Moto Bici ATV da Officina Capacità Max. 700kg Altezza Regolabile 12-38,5cm, Sollevatore Alzamoto con Ruote Officina Operazione Idraulica con Perno di Sicurezza

The motorcycle lift table arrived in a pretty beat up box that seemed to be rolled down a hill before dropped at my parcel box. It was certainly a heavy item that requires a sturdy box/packaging. Unfortunately one of the swivel wheels was badly so that it would not roll at all. There were also a few nuts/screws just floating around in the packaging. I have reached out to support to hopefully replace the badly bent wheel with hopes that I can still use the product. The product seems like it could be great---we shall see. I actually received the motorcycle jack stand as well for a heavier bike and it arrived in a similar way, but with a partially shattered plastic wheel. 2 for 2 broken items was not my hopes for the day.

Mooie en degelijke motorfietskrik. Opgelet! niet bruikbaar bij motorfietsen waar de knalpot/uitlaat onder de motor loopt!

The price is right for a stand like this and it works well and has good features for the price. The biggest problem comes with the hydraulic jack installed on the lift. The jack lowering knob turns difficult and needs to be quite tight to seal correctly. The next problem is when going to jack it up it leaks internally and lowers almost as fast as it elevates. I noticed if I release the foot actuated lift lever quickly it seems to not leak down as if it has an internal check valve that is sticking sometimes. Overall I like the lift and am going to use the heck out of it. It just would be nice if the jack part had a little more quality control and wasn’t so finicky.

It's decent but needs larger wheels. The smallest of pebbles in a garage usually prevents the lift from turning or rolling freely with a load on it.

Nice concept but when I lift my bike it rocks back and forth pretty bad .Hard to trust it up in air

I've bought a lot from vevor. Rarely disappointed. Good build price etc but! Not exactly as described in video and manual. Locking device is shown as 3 dowels welded onto base frame either side for locking device. Mine came with 3 little indents approx 2 mill deep either side for mechanism to register against. Scary ,I'll have to modify to increase safety. Not impressed.

Build quality on its own is quite ok. Price vs quality is very high. Some design errors make it difficult to use though. First is the fit of the lift within the tray. There is too much room/ play on both sides of the lift within the tray causing the lift to slide in de tray itself. I solved this by putting pieces of wood on both sides to make sure the lift is snug in the tray. Second are the choices of the wheels. These are fully made out of cast iron. This makes them sturdy, but extremely difficult to roll under load on a non super flat surface. PU wheels would have been the more logical choice. Third is the lack of bearings in the wheels. Combined with the cast iron wheels, this makes it even more difficult to get the wheels rolling when the lift is loaded. (Which is the whole point of the wheeled tray right).

malheureusement ce produit prometteur n'est pas adapté à ma moto et je pense à beaucoup car il faut un dessous de moto bien plat pour que tout cela reste stable ; demande pour retour en cours

I tried to change my order because I missed the one with the caster. It feels unsafe without the caster, but unfortunately, there is no way to go back to it to change it, and it is very difficult to return the product, and I still have not opened the box. I just have to be careful when buying at this store from now on. Because their policy says "you cannot exchange or buy additional parts unless you buy a new one with it." No, I don't recommend this product and their policy.

my bike that ways just over 400 lbs with no problem. In fact the jack was so easy to raise up I was able to turn the crank lever by my foot while balancing the bike. Tried lifting a Harley Sportster 883 that weighs over 600 lbs with no issue. However, I noticed the lift wasn't lifting the bike evenly. The front shaft that moves on the bottom plate when the lift is raised started to go at an angle. The holes that you insert the safety pin in didn't line up. I'm not sure if the weight of the bike had anything to do with the front shaft lifting at a angle or the lift didn't like the location where it was on the bike. I lowered the bike to see if there was a problem with the lift but it looked normal. I relocated the lift to another lifting point and same issue. Although it didn't look right the lift held up the bike with no problem. I didn't notice anything wrong when I lifted the 400 lb bike. All in all it worked but I not sure if will be an issue next time I need to use it.