Recensioni dei clienti per VEVOR Sistema di produzione di birra, Dispositivo per produzione di birra fermentatore in acciaio inox capienza 30 L, Fermentatore a secchio per birra, Accessori per produzione di birra

This fermenter is amazing! It is super high quality, super top-notch! It is easy to clean, works amazingly. What more can I say? I can't believe the low price for what you get, if you are thinking about this, get it!

Updated: I have left my original story but the end tell my feelings months later. I just recently purchased this product since I have decided to scale up my mead production from 1 gal batches to 5. I will also be brewing beer in the next few weeks using a 5gal kit. Initially unboxing the fermenter looks great, maybe a little dirty. Assembly and setup were easy enough. After mixing my mead ingredients (3gal batch) and pitching the yeast I noticed the following day 2 observations. 1 that the valves leak a little bit at a rate of about 1-2 drops per day. Thats nothing terrible, but honey is very sticky and I worry about sanitation after as they leak from the screws. 2nd is that the metal is thin enough for the fermenter to swell a bit before pushing gas through the airlock, therfore I get a big gas release every few second rather than a continuous bubble. That makes judging my fermentation tricky as I know things are about done when usually get to one bubble every 5 seconds. I could have purchased 4 of the plastic 6.5gal brew buckets with valve for the same price as this fermenter so I give it a meh. Update: I have just experienced my first batch of spoiled mead using this fermenter. I've never had a batch spoil prior to this. I'm going to try and resanitize this and try again but dumping my first 3 gallon batch of mead down the drain is hard to watch. I have since brewed 6 batches of mead or beer using this fermenter and I love it. My early issues were my fault for not doing proper initial disassembly and sanitation. I have 2 plastic bucket fermenters and I greatly prefer this. I've even done 3 lagers in my cold garage this winter. I may buy another.

Well made, good value for money and concise description. Would recommend to any brewing enthusiast.

Purchased two of these and one started rust on the inside seam after the first and only batch and without the use of any harsh chemicals and/or abrasive scrubbers. Rubber feet are awful and are nearly impossible to put back on once they fall off - use super glue your first time and avoid this issue. Otherwise first time home brew went well. Conical are super easy to clean and small enough to move at full capacity if needed. Would buy again for the price!

Très bon produit seulement le prix est un peu élevé je trouve mais à part ça c’est de bonne qualité on va dire

I have two conical fermentors that are from Toledo Metal Spinning that I've been using for many years. This one is no where near as robust as those but this one isn't over $500. I've used this for a couple batches and for the price you can't go wrong. The stainless steel is highly polished and easy to clean. Internal level markings are close enough that they are very usable. Separate bottom drain valve and racking/sample port are nice but I wish the drain port was a size bigger as it can get plugged with trub and yeast. The racking port can be used to get an almost trub and yeast free rack to a keg. While the walls aren't as thick as many fermentors on the market, they are plenty heavy duty for the intended use as long as you don't throw it around it won't dent. The gasketed lid is pretty sturdy and "snaps" on in addition to the clamps to hold it in place. My only complaint other than the bottom valve is the sharp edges on the legs. I'll be adding some silicone edge protector to cover them. I also added a couple extra holes through the lid for a heating element and thermowell. Pretty easy to do using a step drill. I've been using this with the 35l Vevor AIO brewing system. This fermentor doubles as an HLT for sparge water. I heat it with a 1000 watt bucket heater. Very nice combo for an easy brew day.

I love this fermenter yet. I just noticed that now you have come out with a version two and in a larger one which allows for heat control as I brew German wheat beer it has to be held at a certain temperature which is below normal temperatures inside so I’m happy to see that they added that but it’s also over $300 to get that giant fermenter and you don’t get the circulating pump or the coil necessary so that’s the only reason I’ll rate this a little bit lower than usual

It's a bit flimsy in metal thickness but as a fermenter it's large and inexpensive. However, after my first brewing attempt with it I have to say the measurements on the fermenter are way off. I just measured it and you have to fill this fermenter to the 25 liter (6.6 gallon) mark to actually have 6 gallons. Being off by over a half a gallon means not of these markings are right.

This product does not come with a Racking Arm. However, it is well made in every other aspect. I'm gonna have to order a racking arm from somewhere else so I can use it. In it's factory configuration, you're going to pull a lot of trub into your bottles, cans or kegs. Northern Brewer sells their Reactor fermenter with a racking arm and it works great to help keep the yeast trub out.

Performs as described. Includes cooling coil.