Recensioni dei clienti per VEVOR Piegatrice per Lamiera, Piegatrice Portatile da 1220 mm, Angolo di Piegatura 0-135°, Capacità Acciaio a Basso Tenore di Carbonio 20 e Alluminio Calibro 14, con Maniglie, per Piegatura di Metalli
1220 mm
recensioni dei clienti
Come funzionano le recensioni e le valutazioni dei clienti
Le recensioni dei clienti, comprese le valutazioni a stelle dei prodotti, aiutano i clienti a saperne di più sul prodotto e a decidere se è quello giusto per loro.
Il nostro punteggio complessivo non è una semplice media. Diamo priorità alle recensioni autentiche e affidabili ed eliminiamo i duplicati o i contenuti non validi prima di calcolare il punteggio finale. Questo ci aiuta a garantire che la valutazione rifletta fedelmente le esperienze reali dei clienti.
Recensisci questo prodotto
Condividi le tue opinioni con gli altri clienti
Scrivi una recensione
38 Recensioni
Recensioni per l'Articolo Corrente
Acquisto verificato
Solo foto e video
Traduci tutte le recensioni in lingua italiana
Dan Beeman Brake is too flexible!!
1220 mm
It looks beefy but it has too much flex in the center. The ends to center are off by several degrees. I would recommend using with larger gauge than recommended.
0 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
ma*** Qualité de base
1220 mm
La base n'est pas au niveau
0 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
Brian Mr
1220 mm
Handles bent on the first sheet I tried to bend , had to weld on more heavy duty handles, tried to bend a sheet again, found the bend in the middle doesn't bend to the same angle as at the ends
0 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
ROB JONES Description not accurate
1220 mm
This unit bends material but does not bend 20 gauge steel with out flexing if you bend material wider than 15 inches. Thinner material it works also when the bar flexes the pivot pins come out even after installing set screws that were missing apon arrival. As stated it works on thinner sheet metal but not 20 gauge as stated. I am not returning this unit as I will use it for lighter material but will look for something substantially heavier. The price was good the description needs to be updated is all
1 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
Clayton No one important
1220 mm
Do not waste your money. I guess the old adage of you get what you pay for is true. One of the screws that is used to hold part of the brake down to secure whatever material you are bending was badly bent and could not be tightened. Reaching out to customer service provided no resolution, even though follow up emails stated the issue would be resolved in 24-48 hours. It has been over 72 hours and nothing has been done. If I could give zero stars I would. Customer support does not care, they just want your money. Stay away.
0 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
Joe gray Handles need to upgraded
1220 mm
I bought this to bend 14g aluminum sheet and the handles bent first try. I didnt give zero stars becuase other than the handles it seems to built well. Not recomended for the higher end of its limits.
3 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
Kevin Garbage
1220 mm
Disappointed especially i buy a decent amount of Vevor stuff. This is garbage. Doesn't work well and already missing a chunk of metal right in the center of bends. I'd like my money back
0 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
Klint Junk
1220 mm
I bought this to bend 16 gauge aluminum is rated for 14 gauge which is thicker than what I was bending so it should bend it no problem both handles ended up bending on me and it did not make a nice bend needs more reinforcement so the break does not bow under load
0 persone l'hanno trovato utile
Traduci la recensione in lingua italiana
