Recensioni dei clienti per VEVOR Inverter Azionamento a Frequenza Variabile 2,2kW, Regolatore Convertitore Frequenza 3CV 10A 0-400Hz VFD Ingresso Monofase Uscita Trifase Regolatore Inverter di Controllo di Velocità del Motore

pour le moment je n'ai pas réussi à faire tourner le moteur en continu sans obtenir un défaut su le logiciel uccnc ma signalant la perte de données entre le contrôleur uc100 et le logiciel , à aucun moment la notice conseille un câble blindé vers le moteur et des ferrites sur la câble usb alimentant le contrôleur uc100 j'ai du faire une commande de câble blindé et des ferrites ; j'espère que tout sera résolu avec ces aménagements imprévus

Gerät ist einfach zu programmieren. Es fehlt ein Anschlussraum. Kabel sind nicht zu befestigen bzw. abzufangen. Not-Aus-Eingang, der sicherheitsgerichtet ist, ist nicht vorhanden.

This product arrived promptly and was easy to install/ setup etc. Purchased October 2025 and unfortunately failed today. The inverter was a replacement for a 10 year old Delta unit that has been running my lathe over that period. So I would have to say this unit is not in the same class as the Delta unit which were not that much more expensive than the Vevor.

Variateur arrivé en un temps record Pas de chance il est défectueux la programmation est impossible et il se met en défaut Après de bien trop nombreux échanges avec vevor qui n'ont abouti à rien, il m'est proposé 23 euros ( 74,90 payé) Ce que je refuse évidemment je leur propose un échange. Il me propose 43 euros...........ce que je refuse il y a 2 ans de garantie. Et pour finir il mexrembourse 74,90 euros. Quel dommage ces négociation de marchand de tapis Mais bon après pas mal d'énergie dépensé et d'énervement je suis remboursé Mais ça ne me donne plus trop envie de commander chez vevor.... désolé

Il prezzo è buono, la qualità sembra buona ma è ancora presto per un giudizio, si vedrà nel tempo, le caratteristiche sembrano tante, ma con il manuale d'istruzioni a corredo scadente, per usare le sue caratteristiche necessita di prove che possono mettere a rischio il convertitore stesso e per questo ti costringe a usare le funzioni strettamente necessarie, per la spedizione è stata una odissea.

Un manuel d’utilisation en français faciliterait la mise en service Le schéma de câblage ne correspond pas totalement au bornier de l’appareil

bonjour pour l instant je ne suis Pa content après vevor car j ai acheter un convertisseur de fréquence et il n a jamais marcher depuis le début j espère que vevor va faire un geste merci

Pas facile de mettre en œuvre et d’utiliser toutes les fonctions , car la notice n’est pas en français…..

commande non reçu

Obtained this VFD to operate a 3hp Delta Unisaw with a 3phase 220V motor. The VFD does not provide any "enclosure" for connection of input power or 3-phase output. So I utilized a general purpose enclosure underneath the VFD to connect the conduit and bring the individual conductors to the VFD. That enclosure needs to have ventilation to provide for the fans built into the bottom of the VFD. How the VFD is constructed pretty much requires that the VFD be mounted in a vertical orientation, in order for the fans to effectively cool the heatsink. No mounting position requirements mentioned in the instructions. The terminals for connection to the VFD are a screw with a washer under the head. The best connection is a 6mm / 1/4" wide forked spade, although a solid conductor up to 10 guage can fit. If using a stranded conductor, it would be best to solder-dip the conductor for safe and effective connection. The screws for connection are quite short, only screwing out about 4 turns before totally unscrewing, and theres no "stop" to prevent one from totally removing the connection screw. Then, the design of the case is such that it is very nearly impossible to get a connection screw in once removed. Once those installation challenges are overcome, the VFD works great. Press start, and it takes 10 seconds for the motor to gradually come up to speed. A turn knob allows adjustment of speed. In my application, a shop table saw, it would be nice to have big, tactile buttons to push for start/stop, especially the stop. The front panel of the VFD has a membrane keypad, that one must look at and very carefully touch the needed button with a fingertip to get start or stop. There is the provision built into the VFD to connect larger pushbutton switches and relays, to implement more shop-safe start/stop start. Overall it accomplished what I needed, and once I adjust to the slight inconvenience of needing to be more diliberate and careful in turning on and off, will serve very well.