Recensioni dei clienti per VEVOR Forche per Pallet Lunghezza 149cm Capacità Carico Max. 1814kg, Coppia di Forche per Movimentazione Carico da Benne Trattori Minipala Escavatori in Acciaio, Forche per Benne Rimovibili per Carico

Forks great just dont fit my bucket well because of step on bucket. Other than that no problem If bucket was flat would mount great. I just got to build something so they will clamp more securely.

These 4000 lb. pallet forks should have come with a stabilizer bar to limit side to side movement, the same as the smaller forks. Also, the screw down rods (2 each fork) would be much better with a nut welded to the plate and the rod would then screw down into the nut. As it is the nut is attached to the screw rod, and as soon as the nut reaches the plate, the whole plate slips and slides sideways. This causes paint to be removed from the plate and constant repositioning of the plate while tightening.. This would not happen if the nut were attached to the plate as the rod would hold the nut and plate in place.

I bought my forks about a month ago, when I received the box it was torn up and one of the yellow plates was missing. When I put it on the tractor, one of the screws was cross treaded and extremely hard to tighten. Other that that, quality is awesome and very well made. I would buy them again.

It was built really well but they never put the screw rods in the package and you need those to stabilize the forks on whatever you mount them to, and they wouldn’t send me replacements

Verry dissatisfied as it has not held up and I have had to constantly straighten and reinforce to just get by, am looking for alternative.

Perfect item to have, helped out a lot with the farm so far. I am glad I spent the money. Well worth it

Overall good forks. Welds "look" questionable. Tightening handles which are side by side on each fork...occasionally interfere with each other. A weld on one fork is too high or badly positioned....does not let the fork lie flat....so the weld has to be ground down to allow the fork to sit flat on the loader bucket surface.

Bought with high hopes. The one pin to screw on isn’t screwing on properly. Needed a hammer in order to make it move. The forks wouldn’t stay on.

After installing these forks and using them for a while I have found them to be useful but really only because I only have a few things that require forks to lift. The most I am lifting are loads of about 500lbs. I must say that the fork itself feels very sturdy and they seem to be built like a tank. I say "seem" because unlike actual skid steer or similar forks these are made from rectangular box section rather than solid steel plate. Although they are heavy it is difficult to know the wall thickness of the box section and you are limited as to what you can pick up with these forks due to their very thick cross section. These forks will not fit under certain palettes. Again they have held up well with the loads I have lifted but I do not use palettes. These forks also stick out a long way in front of the bucket (in my case 60") and my bucket is 3 feet deep. That puts the load you are lifting a long way out in front of the skid steer and all of that load is being applied to only about 8 to 10 inches of the lip of the bucket. It really doesn't matter that they are rated for 4000lbs. The lip of the bucket will fail long before that 4000lbs could be lifted. The method by which they attach to the bucket is adequate for light loads but it is very difficult to attach the forks securely to the bucket. The large slot at the end of each fork slides over the lip edge of your bucket. Two "L" handle bolts on each fork fasten down on to the "lip" of the bucket clamping the forks in place. This is problematic for several reasons. First there are flared nut fittings that screw on to the ends of the "L" bolts where they clamp down on the bucket. One must be very careful to ensure these nuts have not travelled up the shaft of threaded "L" bolts while tightening. If they have it will be the sharp end of the "L" bolt that bites in to the surface of your bucket rather than the flared foot of the nut. Getting the "L" bolt tight enough while ensuring the flared nut is properly positioned to tighten against the bucket surface is difficult. Before I figured out that the flared nuts were NOT captive on the end of the "L" bolt, I had driven the end of one of the bolts half way through the surface of the metal clamping plate they give you to put between the bucket surface and the bolts. It is also difficult to tighten the "L" bolts enough to secure the forks in place. It is also important to install the forks over the bucket wear bands. This gives them something stronger to press against rather than just the sheet metal of the bucket. All in all these should be considered an inexpensive alternative to proper skid steer or tractor forks and only for light loads. I bought these because I could get them quickly and they allowed me to get my job done while waiting for my actual skid steer forks to arrive. Big difference between these at $175.00 vs. my skid steer forks at $2000.00.

I waited for a long time for the version with the stabilizer bar to become available for purchase and it never did. I reluctantly bought the ones without the stabilizer as they were needed sooner than later and thought I would just buy the stabilizer bar separately when it became available. A couple weeks later (of course) the set I originally wanted became available and I eagerly contacted Vevor for a stabilizer for my new forks, just to be told that it is not available for purchase separately and I should just sell this set of forks and buy a new set! Not impressed to say the least, one would expect parts and pieces/accessories of this nature to be available for your equipment down the line? We did come to an arrangement but I am still without my stabilizer bar I waited so long for. Do better please.