Recensioni dei clienti per VEVOR Calibro per Troncatrice di Precisione, Fessura Standard, Calibro per Troncatrice da Tavolo Lega di Alluminio con Griglia 15 Fermi Angolari, Pistone Caricato a Molla Regolabile Disco Rimovibile

Ottimo prodotto, rapporto qualità prezzo eccellente! Facile da montare, non necessita di regolazioni in quanto le regolazioni di fabbrica sono perfette. Dettagli migliorabili: - Nel cursore di scorrimento manca un elemento per evitare che la guida si ribalti fuori dalla T-track. - Nella parte estensibile manca un supporto per appoggiare i pezzi lunghi da tagliare - Scomoda la lettura della misura in quanto parzialmente coperta dall'indicatore - Andrebbe rimosso qualche millimetro dalla guida per evitare di collidere il metallo con la lama. Temporaneamente risolto mettendo 2 elementi di legno di uguale spessore, uno in testa alla guida, e uno sul riscontro.

The quality is very good, I have put it on my table saw but I haven’t used it yet. The miter gauge is a huge improvement over my original miter gauge.

The small ball bearings do not do the best job at keeping this tight in the slot. The fence is not 100% vertical to the surface of the saw so I had to put some tape between the top of the gauge and the fence. The spring loaded plunger is too small, allowing for movement when dropped into a hole. If very careful applying pressure when using the gauge it does a decent job and is the best available for the cost, as far as I have been able to determine. Can't compete with the $400 miter gauges, but that is no surprise.

Der Anschlag funktioniert soweit gut. Einzig die definierten Einrastpunkte sind schwer zu treffen. Bei mir rutscht der Federbolzen grundsätzlich an den Löchern vorbei und es is ein ziemliches Gefrickel, die richtige Position zu finden.

Reçu dans les délais , outil simple d'une réalisation soignée , emballage très protecteur . Matériel léger destiné à une utilisation amateur mais qui peut durer dans le temps si on est soigneux . Rapport qualité/prix intéressant . ( malheureusement fabriqué en Chine ) . Nécessité de fraiser le guide pour l'adapter à la fente de ma table de scie Lurem mais ce n'était pas une surprise . Précision et fiabilité à voir dans le temps .

Atrezzo molto ben fatto molto preciso e semplice da utilizzare. Arrivato in una confezione molto protettiva. In base al mio utilizzo (hobbystico) lo consiglio

A bit sloppy in my t-track but after some adjusting it was perfect

Nice unit and well built. Accurate straight from factory. My stopper had some machining issues but I quickly received a replacement so I can say that the customer service works very well too. The red indicator of the stopper could be better. I switched it to other side of the stopper hinge to get the gauge away from blade. The t-rail bar should be replaced with one that has eccentric tightening mechanism. The current one is annoying to adjust, needs a lot of threadlock to stay tight and those little ball bearings clog by saw dust. The tension spring in them is so soft that they also need to be basically tensioned until the ball cup scratches the t slot.

Came out of the box as square as any of my current squares allow me to measure… could use a longer miter bar as it gets a little squirrelly near the front of the saw, keeping in mind that my saw doesn’t allow me to use the stabilizer disc underneath the bar… slot is too narrow. Will try to find a smaller disc to use and see if that helps. Micro-adjustment assembly is nice. Extension wing is helpful but has a bit too much play in it at full extension. Overall better quality than expected for the price point.

Not the size for what I Needed it doesn't really fit my power saw table.