Recensioni dei clienti per VEVOR 132.3lbs Incudine Acciaio 60 kg Incudine in Acciaio Blu Forgiatura Rivettatura Appiattimento Formatura del Metallo Lavorazione dei Metalli Trattamento

I'm not a blacksmith, I dont know what a pritchard hole is. I'm just a dude who hammers on ordnance at a BRACed munitions depot for money. I found the scavenged railroad tie plate they gave me for this purpose too soft and bouncy. The anvil surface is hard and flat, and the round horn is handy for opening up pinched 37mm's for inspection and clearing. It has been sitting exposed to cold and very damp weather for a few days and doesn't show any rust yet. The blue paint comes off onto everything that conctacts with it. The casting is rough at the holes in the feet and very sharp in places. I was hoping to lag screw the anvil to a log I was given for a pounding station, but the feet holes are unsuitable for this. I'm not sure if that's a normal anvil feature. I chiseled a pair of recesses into my log so it sits secure enough. Shipping was pretty quick. All in all, I say it beats the hell out of using a tie plate.

I have been making blades for over four years, and wanted a second anvil. I saw the attractive price and decided to try it out. The description says it's cast steel (never purchase a cast iron anvil. Iron is to soft) and it had a 52 hardness. I built a three legged base with 1/4" 2"x2" tubing for the legs and 1/2" plate steel for the base for the anvil to sit on. I filled the legs with sand, tapped the legs with a hammer to get as much sand to compact. This adds weight that you want to keep it from jumping around when using. I dropped a 1" steel ball bearing on the anvil after attaching it to the base from 2' above. The "rebound" of the bearing was 14". When striking some HOT out of the forge 1095 carbon steel with a 3# cross pein hammer, the sound of the strikes were dull and low. (that's what you want) The farther toward the rear of the anvil you strike, it doesn't have the same sound or recoil as the center of the anvil. I also question the hardness of the face. I did manage to put a small dent in the face. I will test the hardness later to see what I get. Overall, it's a great buy at the price! It doesn't come close to my 300#TFS anvil, but it also didn't cost $2,800.00. I would recommend this VEVOR anvil to anyone getting into blacksmithing/bladesmithing, or just needing something to pound on.

Haven't had the time to mpunt it yet, but I did get to hammer on it a little and it's good; the package was obviously dropped and the box was torn, and I had to do the requisite flap wheel dance to slightly round the corners and get rid of paint from the horn, but otherwise I'm pleased with the purchase.

I bought this anvil for two reasons. 1) It has an HRc hardness of ~55, instead of only ~50 which is what the blue ones are. 2) Because the picture shows the horn and round hole being flush with the flat surface of the top of the anvil. This second reason turned out not to be the case. There is about a 1/ to 3/8 inch step there. I have since learned that the step is useful for some things but it does mean the round hole is not the same height all the way round, which makes it less useful for using it as a Pritchard hole. I plan to weld some fender washers onto the end of a pipe that will fit in that hole, and then grind one side flat to fit in the hole and solve this problem. The anvil itself is quite good, and for the price is down right amazing. Edges are sharp, so you can break the corners with a file to set the corner radiuses at the size you want. The anvil rings a bit, but I think with a magnet under the horn and a chain around the base this tones it down nicely. (other anvils also ring and can be quieted the same way)

The horn could be more smooth. I will have to grind it. One of the holes should have been square, but both holes are round. Apart from these things, I am satisfied.

Je suis contente de l'enclume, mais je l'ai reçue avec l'emballage déchiré. Il aurait fallu un emballage plus solide, car il était un peu léger par rapport au poids de l'enclume.

correspond à l'article sur votre site -forme -qualité -présentation -petit bémol l'emballage à revoir -Livraison dans les temps

Bonne enclume, achetée pour débuter dans la forge. Arrivée rapidement avec suivi du paquet. Je voulais pas trop lourd pour ne pas me casser le dos, je suis servi. J'ai dû passer un coup de lime dans les trous pour retirer quelques bavures, rien de bien grave. Je recommande ce produit.

Ok.

Il peso è giusto x i lavori che debbo fare. Il costo è superiore ad altre offerte simili di mercato.